Axiohm A795 Guide de l'utilisateur Page 103
- Page / 128
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
A795 User Guide: Programming Supplement
Chapter 4: Programming commands
103
Erase user flash sector
ASCII GS @ n
Hexadecimal 1D 40 n
Decimal 29 64 n
Value of n: 49 - 50
n = 49 (ASCII n = 1)
This command erases all 64K flash memory sectors
allocated to user-defined character and logos storage.
Those sectors should be erased in two situations: when the
logo definition area is full and an application is attempting
to define new logos, and when an application wants to
replace one user-defined character set with another. In
both cases, all logos and character set definitions are
erased and must be redefined.
n = 50 (ASCII n = 2)
This command erases all sectors available for user data
storage.
Erases a page of flash memory and sends a carriage return
when the operation is complete.
Related information
See command “Flash memory user sectors allocation”
(1D 22 55 n1 n2).
Important: While erasing flash memory, the printer
disables all interrupts, including
communications. To provide feedback to the
application, the printer responds to the
application when the erase is complete. After
sending the erase user flash sector (1D 40 n)
command, an application should wait for the
response from the printer before sending data.
Otherwise, data will be lost. If an application
is unable to receive data, it should wait a
minimum of five seconds after sending the
erase user flash sector (1D 40 n) command
before sending data.
- User Guide 1
- Contents 3
- Where to find the basics 9
- How to use this supplement 9
- Startup Diagnostics 11
- Runtime diagnostics 12
- Remote diagnostics 12
- ********* ********* 13
- ********** ********** 13
- Indicators 14
- Printer configuration 15
- Configuring the printer 16
- Communication interface 17
- Printer emulations 18
- (monochrome papers only) 19
- To run the data scope mode: 20
- To exit the data scope mode: 20
- Overview of commands 21
- Comparison to A793 21
- Standard 23
- Compressed 23
- Cut Edge 24
- Emulation modes 26
- Commands listed by function 27
- Print and paper feed 28
- Text characteristics 29
- Graphics 30
- Batch mode 31
- Real time 31
- Unsolicited status mode 31
- Bar codes 32
- Page mode 33
- Flash download 34
- Command conventions 35
- Perform full knife cut 36
- Clear printer 36
- Perform partial knife cut 37
- Generate tone 37
- Initialize printer 37
- Select cut mode and cut paper 40
- Set current color 40
- Set paper type (ColorPOS™) 41
- Print test form 42
- Print and feed paper one line 43
- Print and carriage return 43
- Feed n print lines 43
- Feed n dot rows 43
- Add n extra dot rows 44
- Print and feed paper 45
- Print and feed n lines 45
- Horizontal tab 46
- Set column 46
- Set vertical line spacing 48
- Set horizontal tab positions 48
- Set relative print position 49
- To move to the left: 49
- Select justification 50
- Set left margin 50
- Set printing area width 51
- Select double-wide characters 52
- Select single-wide characters 52
- Select pitch (column width) 53
- Select print mode 54
- Cancel user-defined character 56
- Select or cancel italic print 57
- Select character size 60
- Download BMP logo 63
- Select bit image mode 64
- Select the current logo 66
- Define downloaded bit image 67
- Print downloaded bit image 68
- Color shade mode (ColorPOS™) 71
- Status command introduction 74
- Transmit paper sensor status 76
- Transmit printer ID 77
- Transmit status 80
- Send printer software version 82
- Preferred implementation 82
- Alternate implementation 82
- Real time status transmission 84
- Real time request to printer 85
- Select bar code height 90
- Print bar code 91
- Select PDF 417 parameters 93
- Sample symbol description: 94
- Select bar code width 94
- Print data in page mode 95
- Select page mode 96
- Select standard mode 96
- Set print area in page mode 98
- Execute macro 100
- User data storage 101
- Erase user flash sector 103
- Switch to flash download mode 105
- Get firmware CRC 106
- Return microprocessor CRC 107
- Return main program flash CRC 107
- Erase selected flash sector 107
- Reset firmware 109
- Appendix A: 111
- Appendix B: 117
- Resident Character Sets 117
- Code page 737 (Greek) 118
- Code page 850 (Multilingual) 119
- Code page 852 (Slavic) 120
- Code page 860 (Portuguese) 122
- Code page 862 (Hebrew) 123
- Code page 865 (Nordic) 125
- Code page 866 (Cyrillic) 126
Produits connexes et manuels pour Imprimer et scanner Axiohm A795
Imprimer et scanner Axiohm 7193 Spécifications
(104 pages)
(104 pages)
Imprimer et scanner Axiohm 7156 Spécifications
(314 pages)
(314 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels