Axiohm A794-D100 Manuel d'instructions Page 53
- Page / 147
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 5: Communication Interface A794 Owner’s Guide
December 199948
Parallel Interface
The printer is also available with an IEEE-1284 parallel interface. The printer
configuration must be set to the parallel interface using the printer’s Configuration
Menu described in the “Diagnostics and Configuration” section of the A794 Service
Guide.
IEEE Bi-directional Parallel Connector
The following illustration shows the parallel communication connector and pin
assignments. The connector is located at the rear of the printer, and is designated as an
IEEE 1284-A receptacle, commonly known as a D-Subminiature 25 pin.
AUTOFD/ (Auto Paper Feed)
FAULT/ (Printer Error)
INIT/ (Initialize the Printer)
SELECTIN/ (Select Printer)
Ground
9
10
11
12
13
14
15
1
2
3
4
5
6
7
8
STROBE/
D0 (Data)
16
17
18
19
20
21
22
23
24
25
D1 (Data)
D2 (Data)
D3 (Data)
D4 (Data)
D5 (Data)
D6 (Data)
D7 (Data)
ACK/ (Printer Accepted Data)
BUSY (Printer Busy)
SELECT (Printer Selected)
PAP_EX (Paper Exhaust)
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Function
Function
Pin Numbers
- Owner's Guide 1
- Legal Notices 2
- December 1999ii 3
- Contents 4
- Chapter 1: About the Printer 6
- Description of Printer 7
- Models Available 8
- Features 9
- Chapter 2: Using the Printer 10
- Unpack the Printer 11
- Choose a Location 13
- Connect the Cables 14
- Cash Drawer Cables 15
- Power Supply Cable 15
- Printer Controls 16
- Loading Receipt Paper 18
- Configuring the Printer 21
- December 1999 17 22
- Troubleshooting the Printer 23
- Printing Problems 24
- Printer Does Not Function 24
- December 199920 25
- Ordering Thermal Paper 26
- Ordering Cash Drawers 28
- Ordering Communication Cables 29
- Wall-Mount Kit 29
- Characters 31
- Paper Specifications 32
- Print Zones 32
- Print Zones for 82.5 mm Paper 34
- Character Sets 37
- Code Page 850 38
- Code Page 852 39
- Code Page 858 40
- Code Page 860 41
- Code Page 863 42
- Code Page 865 43
- Code Page 866 44
- Code Page 1252 45
- Communication Overview 47
- RS-232C Interface 48
- XON/XOFF Protocol 49
- DTR/DSR Protocol 50
- Power Connector 51
- Cash Drawer Connector 51
- RS-232C Settings 52
- Parallel Interface 53
- Command Conventions 55
- List of Commands and Location 56
- By Function 60
- Print Characteristic Commands 61
- Graphics Commands 62
- Barcode Commands 63
- Comparisons 65
- Command Descriptions 66
- Perform Partial Knife Cut 67
- Generate Tone 67
- Initialize Printer 68
- Bit Sensor 0 1 70
- Sensor Status 70
- Select Cut Mode and Cut Paper 71
- Print Test Form 72
- Print and Feed One Line 73
- Activate Carriage Return 73
- Print Lines 73
- Dot Rows 74
- Extra Dot Rows 74
- Set Line Spacing to 1/6 Inch 75
- Set Line Spacing 75
- Print and Feed Paper 76
- Print and Feed 76
- Horizontal Tab 77
- Set Column 77
- Set Horizontal Tab Positions 79
- Set Relative Print Position 80
- Select Justification 81
- Set Left Margin 82
- Set Printing Area Width 83
- Select Double-Wide Characters 84
- Select Single-Wide Characters 84
- Select Pitch (Column Width) 85
- Select Print Mode 87
- Cancel User-Defined Character 90
- Select or Cancel Italic Print 92
- Select Character Size 93
- Character Width Selection 94
- Hex Decimal Width 94
- Character Height Selection 94
- Hex Decimal Height 94
- Summary of Rotated Printing 96
- Download BMP Logo 98
- Select Bit Image Mode 99
- December 1999 95 100
- Related Information 100
- Select the Current Logo 103
- Define Downloaded Bit Image 104
- Print Downloaded Bit Image 105
- Status Commands 106
- Value of 107
- Function Description 107
- Bit 0 Bit 1 107
- Status Byte 108
- (RS-232) 108
- Type ID ( 109
- ASCII Hex Dec 110
- Real Time Commands 115
- Auto Status Back 122
- Bar Code Commands 126
- Print Bar Code 127
- Select Bar Code Width 128
- Page Mode Commands 129
- Print Data in Page Mode 130
- Select Page Mode 130
- Select Standard Mode 131
- (x0, y0) 132
- (x0 + dx, y0 + dy) 132
- Print Area 132
- Macro Commands 135
- Execute Macro 136
- User Data Storage Commands 137
- Erase User Flash Sector 139
- Flash Download Commands 140
- Get Firmware CRC 141
- Return Microprocessor CRC 142
- Return Main Program Flash CRC 142
- Erase Selected Flash Sector 142
- Reset Firmware 143
- A794 Owner’s Guide Index 144
- December 1999 139 144
- Index A794 Owner’s Guide 145
- December 1999140 145
- December 1999 141 146
- © 1999 AXIOHM 147
- Printed in U.S.A 147
Produits connexes et manuels pour Imprimer et scanner Axiohm A794-D100
Imprimer et scanner Axiohm 7156 Spécifications
(190 pages)
(190 pages)
Imprimer et scanner Axiohm 7193 Spécifications
(104 pages)
(104 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels